What does encrypted transmission mean on a Philips TV. Setting up digital channels on a Philips TV. Remote control configuration in semi-automatic mode

D101-0

Cause:
The TV did not have time to transmit service information available in the TV signal stream to the CAM module

Solution:
Switch to the encrypted channel and wait 3-5 minutes until the TV completely transfers all service information from the TV signal to the CAM module.
Setting the date and time on your TV correctly can also help.

E006-4, 104-2, E106-9, E106-9, E04-4
or "Status Uncertain"

the smart card was inserted incorrectly
dirty smart card contacts
smart card failure
a smart card not from MTS is used
The smart card is not suitable for this set of equipment
The set-top box or the card reader in the set-top box is faulty

reinstall smart card
clean smart card contacts (without using harsh cleaning materials or detergents)

E101-4, E107-4

The card did not receive the non-activation command
The command to activate this card was not sent
The MTS smart card is installed in a third-party receiver, i.e. not a receiver or cam module MTS (E107-4)

Solution:
Call technical support to request equipment activation

E016-4, E16, E16-4

There are not enough funds on your personal account balance
not subscribing to a certain channel

Top up your account or switch to another channel if an error occurs when trying to watch an unpaid channel package

E106-9

A smart card not from MTS is used
Factory defect of smart card

Use the smart card that was included with the MTS set-top box/cam module. If you use an MTS smart card, contact technical support.

E030-4, E120-4

On the TV to which the TV module is connected, the date and time are set incorrectly.

Set the exact time and date on your TV using the TV instructions. If this does not resolve the errors, disconnect the TV module from the TV and connect it again.

E019-4

TV with cam module did not turn on for a long time

Check for a smart card in the device, make sure the cable is connected to the TV, then leave the TV on for a few hours or call technical support to request reactivation.

E133-4

E48-32

Update the software version
Reset the settings to factory defaults and start searching for channels again
Try removing and reinserting the SMART card

E107-4

The smart card is not activated. Request equipment activation from technical support.

E52-32

there is no satellite signal

Check the quality of all cable connections for mechanical damage. Check the integrity of the converter, as well as the antenna settings. After eliminating the problem, reset the set-top box settings to factory settings and start a new channel search.

No error code or error D101-0

Inscription on the TV screen: CI+ ERROR: Host Certificate Invalid-Expiried, Please Tune to DTV service - 16 (Сl+ ERROR: invalid Host certificate, expired, please switch to another program)

To solve the problem, reset the TV or set-top box to factory settings and start a new channel search. If this error appears on your set-top box, you may need to update the software.

Host error, expired, switch to another program

This error occurs when using the cam module. To fix it, set the correct time on your TV.

Knowing that a Philips TV has a high potential for technical capabilities, many of its owners sooner or later wonder how to set up Smart TV on a Philips TV themselves, without outside help. After all, this Smart setting allows you to get a multifunctional smart TV receiver with access to an unlimited number of Internet resources.

It looks good in strong light, but the house is too aggressive and boring. Unfortunately, it is also common to set the home mode to factory settings, so that in the long run it is tiring to the eyes and, contrary to appearances, does not always provide optimal image quality.

Fortunately, we can eliminate most defects and adjust the settings to our preferences. We have prepared calibration guides for TVs from five popular manufacturers. On most new TVs, picture settings only apply to the currently selected input source.

Philips Smart TV installation has two technical options.

Method one: wireless

Turn on the router.
Find a special USB connector on the side panel of the TV receiver.
Insert the adapter into the USB connector.
To configure the wireless offer, you need to press the WHS button on the router.
Wait approximately two minutes.
Find the line “Easy access” in the menu, confirm the selected function with the OK button (if necessary, upon request, enter and confirm the PIN code. Click in the Pin Code menu - OK - insert the suggested PIN).
When prompted for a security key, the sequence is as follows: Install. User – OK – dial the key on the TV remote control.

This action program will allow the configured TV to join your home network. If more than one router is found, the network is selected using the Scan buttons. and Easy access.

Quick image calibration in 10 steps

Then move the cursor to the end of the menu. Then the position of the picture settings will be set. It launches the main menu of the TV, where the first tab is responsible for the image settings. We've prepared a quick calibration chart for you that will allow you to set up your TV shot in just 10 steps. For each setting, we've also developed a legend explaining what it means and how it affects image quality. You will learn what the image parameters are in the second part of our guide.

Method 2: wired connection

With this method, to connect to the smart you need an Ethnernet FTP cable and a router.

Connect the router to the TV receiver and turn on the conductor.
Press the button on the remote control with the image of a house.
Select Settings – Network connection.
Follow the menu items and instructions on the screen.
Confirm the request for an agreement with the terms and conditions for the user.

If you don't want to use our 10-step method, we invite you to the third part of this guide, where we will help you perform manual image calibration using test images. Below is a short tutorial on how to read our table.

The table below lists all the most important settings for the five brands we've chosen - along with the optimal picture settings. The included remote control is a universal remote control and can also control most commercially available television models. To control your TV, you must configure the remote control for your receiver model.

How to set up IPTV on Philips TV

Setting up IPTV on a Philips TV is done through the ForkSmart smart TV widget. The sequence of actions is as follows:

Go to Philips setup.
Click view parameters.
Write down the numbers and letters that appear on the screen.

Wanting to connect digital television, many people turn to companies that provide these services. These companies offer everyone to set up free digital TV channels for a certain amount. Most clients agree to this, and do not even know that it is not necessary to do this.

Remote control configuration in semi-automatic mode

Enter the two-digit code corresponding to your TV brand. Step Press the mute button while pointing the remote control towards the TV. Each subsequent press of the button sends a different code for the selected brand of TV. The pilot will remember the correct settings.

Step Check that the TV is working properly. If not, program the remote manually by hand. Enter the three-digit code corresponding to your TV brand by pointing the remote control at the TV. If the entered code is correct, the remote control will send a mute command to the TV. Check that the TV is working properly with the remote control.

You can set up DTV on almost any TV. The only thing that is required for this is the presence of a tuner, which can be built-in or external. It all depends on the brand of your TV and its model. Most modern TVs have this feature. The main thing is that it is a foreign-made device and was released no earlier than 2005-2006.

Repeat programming by re-entering another code from the list for your TV brand. Turn on the decoder and TV using the reserve key. This module allows you to view encrypted channels without purchasing or renting a dedicated set-top box. The movement of the largest satellite platform in Poland only confirms the prevailing trend of modules. Is this phenomenon about freedom of choice for users or perhaps a relief for platforms?

Until now it has not been a highly professional product, rather dedicated to the most demanding and familiar with satellite technology for customers. However, new televisions equipped with satellite receivers have expanded the horizons of this solution. Everything indicates that we will have a real modular offensive. Selecting a module is often an opportunity for the user to control an additional device. Many televisions are designed to receive Polish satellite platforms. Plus, we all control it with a standard TV remote control, so there's a lot less hassle for the user.

Televisions from Philips are quite popular in Russia. This is due to their reliability, quality, prevalence and relatively low cost. Today we will talk about how to set up digital TV for those who also have a device from this company.

Setting up channels on TVs before 2011

The interface of many Philips TVs is different from each other. However, the general scheme for installing digital television on them is as follows:

The only drawback of this option today is that few TVs on the market have two satellite tuners, which means that we cannot watch one channel at the same time while recording another. This problem will probably be resolved in the coming years. Access modules are also great for sports enthusiasts and advanced decoders. Football fans will likely not be able to access exclusive channels across all digital platforms. With modules instead of three decoders, they can connect modules to an advanced decoder and take advantage of the full range of satellite platforms.

If during these steps your TV starts asking for a password, then you will need to enter 0000, 1111 or 1234. These are standard passwords that will give you access to certain options.

Modern Philips TVs

More modern models are configured in almost the same way, but there are some features.

To set up a modern Philips model you will need:

If you choose quick scan, then you will need:

Set the frequency difference to 8 MHz;
Disable analog channels if you already have them configured, click “Finish” and start searching.

If you want to perform a full scan, then:

In network frequency mode, select “Manual”;
Next you should set QAM – 256 and frequency – 298.00;
After this, you will also need to turn on or off the search for analog channels and start searching.

If everything was done correctly, your TV will start broadcasting free digital channels available in your region.

Subscribe to news

First, we read the stickers on the back wall of the TV, where separately for each tuner (DVB-T and DVB-C) there is a list of countries in which, according to Philips, there is digital broadcasting (at the time the TV was released, but if you update the firmware through their official website, this list may change in subsequent firmware). If our country is not there, then we will have to put some other one from this list.

2. select - "Configuration"

3. select - "Installation"

6. select - "Digital mode"

7. select - "Cable"

8. select - "Automatic"

9. click - "Start"

Instruction No. 2

Philips TV models 2011

1. Click on the icon - “House”

2. select - "Installation"

3. select “Search for channels”

4. select - "Reinstall channels"

5. select - “the country indicated on the sticker on the back panel” (usually France, Finland or Germany)

6. select digital mode - “Cable (DVB-C)”

7. In the “Network frequency” line, enter the frequency

8. in the line “Transfer speed” enter

Setup takes approximately 5-10 minutes.

Instruction No. 3

1. In order to set up high-definition digital TV channels for the vast majority of Philips models, press the “Menu” button on the remote control, you will see the TV menu in which you will need to select the “Configuration” section

2. Select the Installation tab. After clicking OK, you will be taken to the second menu field, then go to the Channel Settings tab. After clicking the “OK” button, the third part of the menu will open, where you need to select “Automatic”. Installations". Next you will see a message about updating the channel list, click “Start”

3. Select "Reinstall Channels"

4. In the Country section, you must select Finland; if this country is not in the proposed list, then select Germany

5. Since you are connecting to digital television via a DVB-C cable network, you must select “Cable”

6. Before you start searching for channels, select “Settings” to manually correct the search parameters

7. Set the baud rate to manual mode. In the tab, manually change the transmission speed from the control panel to the desired one. In some TV models, the flow rate is indicated in the “Character 1” tab; “Character 2” is left at 0.

8. Now set the network frequency to manual mode and enter the network frequency from the control panel

9. After clicking the done tab, you will again be taken to the channel launch menu, now you can start scanning

10. If you did everything correctly and saved all the changed parameters, then during the search your channels will be detected.

Modern TVs require preliminary setup: connecting to the network, searching for channels. In general, the procedure is intuitive: you just need to trust the system prompts. However, some users still experience difficulties. Below we provide a detailed manual for Philips TVs.

If the box from the device has been preserved, then it should contain a brief specification indicating support for the DVB-T2 format. Similar information can be found in the operating instructions. If there is no documentation, then it is worth inspect the back panel of the TV. The interface marked DigitalInput indicates that the model supports digital TV.

Important! Devices manufactured before 1998 do not work with the DVB-T2 format. Until 2004, equipment was only partially equipped with digital outputs: these were expensive TVs with a diagonal of more than 40 inches. The format began to be implemented everywhere after 2005.

That's all the difficulties of how to set up digital channels on a Philips TV when it has the functions of a modern Smart TV. Perhaps the following video will help many users when making such settings:

Setting up channels on a Philips TV does not require special knowledge. Just follow simple instructions. Automatic channel tuning saves time and simplifies the setup process.

You will need

Philips remote control

Instructions

Find the button on your remote control that says “MENU” and press it. From the list that opens, select the “Configuration” or “Settings” section.

Next, go to the “Settings” item.

Select Channel Settings. Then - “Automatic configuration” and “Start”.

Next - “Reinstall channels”. After this, you need to select any country that has an official digital cable television broadcasting system. Some TVs have a list of such countries on the back.

Now select the “Cable” section, “Settings”. Before starting the search, you need to specify the baud rate mode - “Manual” and set the baud rate.

You also need to specify the frequency scan: fast or full. It is recommended to install "Quick Scan". You can select “Full Scan”. It will take about 30 minutes and you don't need to complete the next step.

Set the network frequency mode to “Manual”.

To find not only digital channels, but also analog channels, set it to “On”. Next, click “Done.”

Now you need to start the search. To do this, click “Start” and wait for the search to complete. When finished, select “Done”.

Channel setup is complete. To exit the menu, you can press “BACK” or “TV”. Enjoy watching!

Rate the article!

Digital television has undoubted advantages over analogue: the quality of the transmitted picture, greater resistance to interference, as well as other, less important advantages.

However, to appreciate the quality of digital television, you must have a latest generation TV. As an example, let's try to configure digital channels on a Philips TV.

Quick navigation through the article

TV menu

First of all, you need to get to the TV menu: to do this, press the “Home” button on the remote control;
Next, in the menu you need to find the “Configuration” item and in the menu that appears we find the line “Installation”, and then - “Channel settings”. It is at this point that you can configure both analog and digital channels.

Installing and updating channels

The next step is that you need to choose whether you will use channel reinstallation on your TV or just update.

If you choose to reinstall, all already installed channels are deleted and reinstalled. For initial setup, naturally, choose this mode. Digital channels can be configured in the first hundred, followed by analogue ones.
The update is best used when reconfiguring. In this mode, all installed channels will remain, and new ones found will appear at the end of the channel list.

Continue setting up

Next, you will be asked to select a country (choose Finland). In principle, you can choose any country that has official cable digital television.
Then select “Cable” (if, suddenly, this item does not appear, then you have chosen the wrong country).
The next step is to set the search settings - this is the only way you can properly configure digital channels. The transmission speed is set manually (and the speed itself is 6.875).

Scan selection

Frequency scanning is possible in two versions: fast and full.

A full scan will take too long, so set it to "fast". Again, select the network frequency manually and its digital value is 290.00;
Next, if you want to configure not only digital channels, but also analogue ones, then mark them enabled;
Finally, click “Finish” and the channel search will begin.

The search usually lasts approximately 15 minutes. After its completion, you can return to the beginning of the menu and view the configured digital channels.

Share this article with friends on social media networks:

Philips Smart TV installation has two technical options.

Method one: wireless

You can set up access to smart TV on your home screen via a Wi-Fi network. In order for numerous applications to become an integral part of Philips, it is necessary to use the help of such technical guides as:

router supporting Wi-Fi network;
wireless adapter (PTA01).

Philips Smart TV connection sequence:

Turn on the router.
Find a special USB connector on the side panel of the TV receiver.
Insert the adapter into the USB connector.
To configure the wireless offer, you need to press the WHS button on the router.
Wait approximately two minutes.
Find the line “Easy Access” in the menu, confirm the selected function with the OK button (if necessary, enter and confirm the PIN code upon request. Click in the Pin Code menu – OK - insert the suggested PIN).
When prompted for a security key, the sequence is as follows: Install. User – OK – dial the key on the TV remote control.

This action program will allow the configured TV to join your home network. If more than one router is found, the network is selected using the Scan buttons. and Easy access.

Method 2: wired connection

With this method, to connect to the smart you need an Ethnernet FTP cable and a router.

Connect the router to the TV receiver and turn on the conductor.
Press the button on the remote control with the image of a house.
Select Settings – Network connection.
Follow the menu items and instructions on the screen.
Confirm the request for an agreement with the terms and conditions for the user.

How to set up IPTV on Philips TV

Setting up IPTV on a Philips TV is done through the ForkSmart smart TV widget. The sequence of actions is as follows:

Go to Philips setup.
Click view parameters.
Write down the numbers and letters that appear on the screen.

Using the Philips PFL-8404H TV as an example

1. Press the “House” button on the remote control and get to the menu.

2. Select “Configuration” from the menu.

3. "Installation".

4. “Setting up channels.”

5. "Automatic installation".

6. “Start.”

7. “Reinstalling channels.”In this case, the current channel settings will be deleted and all channels will be found again. The list of channels will be located starting from the 1st in the order they are found during the search. Analogue channels will be located from the next hundred after digital ones. Select this mode when setting up your TV for the first time. Or to completely reconfigure it.

"Update channels"- in this case, the already configured channels will remain in their places! Newly found channels will be added to the list after existing ones. Select this mode if you do not want to lose the location of the current channel setup.

8. "Finland". You can choose any country that officially broadcasts digital cable channels.

ATTENTION – there is NO such broadcasting in Russia. (and even when it appears, you will need to wait for the manufacturer to update the TV firmware)

9. "Cable". If there is no such menu item, it means either you have selected a country without digital cable, or your TV does not contain a DVB-C receiver.

10. "Settings". Don't start searching! First, “Settings”!

11. Transfer speed mode – “Manual”.

12. Transfer speed – “6.875”.

13. Frequency scanning. "Quick Scan" You can leave “Full scan”, but skip the next two steps. But keep in mind that a full scan will take about half an hour!