My iPhone 6 is hot and won't turn on. What to do if your iPhone turns off and won’t turn on. Solving the problem yourself

How the repair works:

• 1 We diagnose the imported goods for free
  device received by you or our courier.
• 2 We carry out repairs and also provide a guarantee on new installed parts. On average, repairs last 20-30 minutes.
• 3 You receive a working device yourself or call our courier.

So, if you put your phone on charge and it turns off, most likely the problem is related to the usual system failure when the gadget is rarely rebooted. In this case, turning on the iPhone 6 will help by pressing and holding two buttons for 30-35 seconds: “Power” and “Home”. The brand logo should appear on the device screen, after which the smartphone will boot into normal mode. But what to do when the causes of the malfunction are not related to a system freeze?

If you find yourself in a situation where the iPhone 6+ does not boot when powered, most likely there is a problem such as damage to the "Power" button. Examine her, if she does not respond, seek help from service center, where they can repair it and conduct a comprehensive diagnosis of the gadget. In addition, the liquid contact indicator may be damaged or in poor condition. Examine it carefully; if you see signs of corrosion, they can only remove it at a service center.

Another cause of this problem could be a faulty power adapter. In this case, the charger needs to be replaced. Also check if your smartphone battery has failed. To change the battery, it is best to contact an official or trusted store.

Sometimes the problem with the iPhone 6 Plus turning off when charging lies in a defective or non-original charging cable. The solution to this problem is to purchase a genuine cable. Also, do not exclude the possibility that the device itself may be defective. Therefore, as a last resort, you should contact the store where it was purchased to replace the device.

What to do when your iPhone stops turning on

In addition to all of the above, the iPhone 6 Plus may not turn on when the battery is powered if it is very low. Leave it charging and try to turn it on after half an hour. Typically, when the phone is sufficiently charged, a charge indicator should appear on the device display and home screen. In this case, the Apple smartphone is ready for use. If the icons appear, but the gadget does not turn on even after charging, we advise you to seek professional troubleshooting help.

Connect your device to your computer. If your iPhone 6 Plus is recognized but appears to be in recovery mode, try running recovery mode. This function will help fix a software glitch. If the Apple smartphone is not in the list of iTunes devices or the device could not be restored, then a comprehensive examination and repair is necessary, so contact the service center immediately. After all, only professionals in their field will help eliminate device malfunctions.

Almost all owners of Apple gadgets have to get acquainted with the unpleasant situation when the iPhone 6 does not turn on - that is, when there is no response to any commands. Observing a non-working phone, the owner scrolls through the worst-case scenarios in his head, but there is no need to panic.

If there were no falls from a height, or the gadget did not come into contact with a “wet” environment, then everything may not be so scary. In this article we will provide a list of the main reasons that can lead to a sudden shutdown of the phone, and we will also name the most effective ways, allowing you to eliminate failures.

If your iPhone 6 is dropped and won't turn on, there is a possibility that the connection module was damaged due to impact. battery charging. This microcircuit recharges the battery from the charger unit. When this element is damaged, the iPhone stops charging both on and off (in the second case, you simply will not be able to turn on the gadget).

By the way, due to a breakdown of this module, the iPhone may not be charged from USB. A damaged charging module leads to disruption of connections between the battery and other telephone systems. Whatever the reason for its failure, the module needs to be replaced.

Checking the battery

The most common, simple and fairly obvious reason for a phone not turning on may be a dead battery. If the screen on your iPhone 6 goes blank and won’t turn on, what should you do? Of course, it is advisable to put it on charge. Moreover, it makes sense to wait about fifteen minutes from the moment you start charging before trying to turn on the gadget again. This is necessary so that the incoming energy charge is enough for system activation.

If you use a non-branded charger (for example, at work), due to poor contact, the battery may not receive a full charge, as a result of which it will run out much faster.

You can, of course, change the battery yourself - there are many instructions on this on the Internet. However, if you do not have confidence in your own abilities, then it is better to consider Charger, and the gadget to the service center - as a result, you will not lose the warranty from the manufacturer.

There is a possibility that the iPhone 6 does not turn on after being discharged due to broken or dirty cables and charging ports. Try to clean all the input and output ports, and also change the charger, preferably a branded one. Often the port becomes loose while charging the phone in the car. No matter how reliably it (at first glance) is fixed, it is necessary to understand that constant shocks and vibrations during the trip negatively affect the quality of the connection.

Other models of Apple equipment may occasionally experience problems, for example:
Why iPhone 7 won't turn on
Why iPhone 5s won't turn on and how to fix it

Hardware problems with iPhone 6

Problems with hardware can also arise due to motherboard, whose injuries are most often caused by falling. Among the obvious signs of a breakdown are: spontaneous reboots, loss of sound, the appearance of a red screen and, at some point, the device’s refusal to turn on. Only a “major” repair will save the gadget in such a situation.

If the screen of the iPhone 6 does not turn on, this may be evidence of a loose contact or failure of the display. His service replacement It costs half the price of a brand new device, since it is replaced as a whole unit - Apple does not produce individual spare parts.

Sometimes it is enough to secure the corresponding cables more firmly and replace the frayed cable with a new one.

In addition, the problem may be a blocked or broken power button, especially if the phone got wet or fell shortly before. Needs to be removed protective case, wipe the button and grooves. If there is no visible damage, there is a need to open the device.

iPhone 6 software errors

If the iPhone 6 does not turn on after an update or the gadget suddenly turns off when fully charged and does not respond when you press the Power button, there is a possibility that it has gone into a special saving mode - turning off on its own in order to reboot. Try pressing two buttons at once - Power and Home, holding them pressed for about 20 seconds. As a result, a reset and standard reboot will occur, after which the device should start.

Video

When using Apple technology, an unpleasant situation often occurs when your iPhone turned off and won't turn on. This scenario applies not only to iPhone smartphones, but also to the popular line iPad tablets. In these cases, you should not sound the alarm in advance, get upset, worry, and especially not take your Apple gadget to a special service center. First, calm down, carefully consider your actions and follow the instructions below.

In the vast majority of cases, a number of similar situations are not even a breakdown; the device simply stops responding to button presses and does not turn on. Use two universal ways, which will make your device work.

The main two reasons why and refuses to work, it is either a low battery charge in the smartphone, or a banal system freeze, which has recently been increasingly happening with Apple technology.

These problems are not related to hardware or even more so software errors, for the solution of which it is necessary to take the devices to specialists or repairmen.

You can solve the problem yourself by connecting the phone to the charger and leaving it in a quiet state on charge for 10 - 15 minutes. The battery icon should light up on the black screen of the gadget. This means that the device's battery is completely discharged and you need to wait a bit. After the specified time, try turning on the smartphone without unplugging the device from the outlet.

If the reason is that your iPhone or iPad is frozen, you need to force reboot the system.

The screen is dark and the iPhone does not turn on - does not respond to button presses

The option when the iPhone does not turn on, much less respond to button actions, has recently become a fairly common occurrence in Apple phones and tablets.

The standard situation occurs as follows: the iPhone or iPad has not been used for a long time, while the device is fully charged. At one point, for reasons unknown to you, the gadget turned off and no longer wants to turn on. At the same time, pressing the start key of a smartphone or tablet, the screen does not light up. What to do and what to do if your iPhone or tablet does not turn on?

The main thing is not to panic. There is nothing scary or dangerous in this, since mobile devices from time to time they can go into “save mode”, which is similar to the indicated symptoms, especially when the gadget is rarely rebooted and used.

A universal method for “reanimating” an iPhone or iPad tablet

If your iPhone or iPad tablet is charging but won't turn on, use a simple sequence of actions that is suitable for most models of the manufacturer and will help “reanimate” a frozen device: press and hold the “Power” key and the “Home” button at the same time for 10 to 20 seconds. As a result, the apple logo should light up on the gadget’s screen, and the device will continue to load.

These instructions apply to the following manufacturer gadgets:

• iPhone 2G;
• iPhone 3G;
• iPhone 3Gs;
• iPhone 4;
• iPhone 4s;
• iPhone 5;
• iPhone 5c;
• iPhone 5s;
• iPhone 6/6 Plus;
• iPhone 6s/6s Plus;
• iPhone SE;
• Any version of the iPad.

If the iPhone still does not turn on, the apple lights up and the screen goes blank, most likely the error is more serious, hardware or software. In this case, you need to either change the charger or the phone battery. This can be done at a company service center.

Method for new versions of iPhone 7 / iPhone 7 Plus smartphones

The option to enable new Apple smartphones, iPhone 7 and iPhone 7 Plus, is slightly different from universal method. This is due to the fact that the “sevens” have a built-in touch “Home” key instead of a mechanical button. By simultaneously pressing and holding the “Power” button and the volume down key for 10–20 seconds, the user activates a special wake-up mode for the phone. The company logo will appear on the display and the device will boot into normal mode.

Often mobile gadget may freeze while running one of the programs that caused the iOS system to crash. In this case, the buttons do not work, and it is necessary, by analogy with the previous situation, to start the process of forcing the phone to reboot.

The above examples constantly arise with most of the manufacturer’s devices. A list of guidelines solves the vast majority of them, but if you're unlucky and your device still won't boot, then it looks like you might be experiencing one of the following problems.

There could be several reasons why iPhone 6s is disabled and in simple ways I can't enable it:

1. smartphone is discharged,
2. the smartphone has become too cold,
3. The smartphone is in “save” mode
4. There has been a breakdown software,
5. smartphone components are damaged.

Read on to learn how to turn on your iPhone 6s in each of the above situations.

iPhone 6s is low and won’t turn on – there’s a blank battery indicator on the screen

Naturally, after the phone is discharged, it will turn off. If, when you try to turn it on, a blank battery indicator appears, then you just need to put the smartphone on charge. It will not turn on immediately after this - you need to let it recharge. This can take up to an hour, depending on how long the iPhone has been discharged.

When you connect the charger, the image on the screen will change. If this does not happen and the image with a blank charge indicator still hangs, then the problem is either a faulty connector or a charger. Try charging the device with a different charger. If it doesn’t work either, then you need to go to specialists.

The smartphone is overcooled

If you use your iPhone in the cold, it will quickly discharge and turn off. Read more about this problem and methods for solving it in the article “”. The solution to the problem in this case is the same as in the past, but with one addition: before charging the phone, you need to let it warm up to room temperature. Let it sit for half an hour, and only then charge it. If you connect a cold iPhone to a power outlet, condensation may form and the components will fail.

The smartphone is in “save mode” - there is nothing on the screen and the phone does not respond to buttons

To "save mode" Apple smartphones switch if you rarely reboot it. What should I do to turn on my iPhone 6s in this case? Press and hold the Power and Home buttons simultaneously for 15-20 seconds. The smartphone should turn on.

A software failure has occurred - the smartphone freezes during the startup process

It happens that you try to turn on your iPhone 6s and it gets stuck on the Apple logo screen or just shows a red/blue screen. Then you need to restore the firmware. To do this, you will need a cable and a computer with iTunes installed.

• Connect your smartphone to your computer and open iTunes.
• Force the device to restart by holding down the Power and Home buttons. After 10 seconds, release the power button, but continue to hold “Home” until the recovery mode screen appears.
• A window will appear in iTunes asking you to restore or update your device. Select Update.

If after iPhone updates 6s won't turn on, don't be alarmed: it just needs to be forced to restart again by holding down the power and home buttons.

Nothing helps? This means that the problem is the broken elements of the smartphone

If none of the above methods help, then the problem is most likely in broken internal components of the iPhone. Contact the warranty service center, they will tell you everything for sure. If you have RosTest, you can come to any official service center apple center. Owners of EuroTest models need to contact the store where the iPhone was purchased with a warranty card.

Everyone may face a situation where iPhone is charging, but it doesn’t work. Perhaps the reason for the breakdown is serious, and you will have to repair the phone at a cost. But in a number of different cases (for example, if the connector is dirty or a software failure has occurred), you can fix the problem at home without experience, qualifications or tools. But not many people know how to connect a phone to a TV, and in this article we will look at 6 ways to display an image from a phone to a TV. It’s worth trying to find the problem on your own and get your phone working again.

What are the causes of iPhone malfunctions?

Many iPhone owners experience difficulties: the device charges slowly or does not turn on at all. And if a small problem (for example, a broken Home button) is not so critical, then in such situations it is impossible to use the phone.

Main reasons for the malfunction:

• important internal parts (tristar controller, synchronization cable, power controller, motherboard or battery) are damaged due to mechanical impacts (shocks, falls) or liquid spills
• a faulty, non-original charger is used (available Chinese counterfeit)
• failure of the Lighting connector or its contamination caused by dust, hair, lint and other small debris
• software failures (software directly affects the chip that controls the charging process)
• The USB port of your tablet or desktop computer is broken
• manufacturing defects Apple devices involved in the battery charging process

Errors during program operation, breakdowns of chargers and iPhone parts (batteries, connectors, cables, etc.) can manifest themselves in different ways. A few examples:

• iPhone won't turn on after being discharged (when the battery runs low)
• the application hangs, does not respond to presses, or the screen is one hundred percent dark
• The device turns on, but hangs after the Apple logo appears
• the indicator lights up, but the charge level is very low even over a long period of time
• The iPhone is dead and won’t turn on when charging from the cigarette lighter or computer

Before taking your phone to a service center, make sure that the cause of the malfunction is a hardware failure. And under no circumstances do not delay your trip or call a repairman if you have spilled iPhone water - every hour of delay can worsen the situation.

How to get your iPhone back working

When faced with power-on and charging dilemmas, first check to see if there is current in the outlets. What to do if the iPhone does not turn on but the apple is on fire. Next, if the phone does not turn on at all, connect it to the charger. In its normal state, the device immediately writes that it is charging - the indicator lights up, which means the process is in progress. Please remember that the battery is not designed to operate in low temperatures. Therefore, warm up the phone before connecting the charger if the battery runs out in the cold.

Another situation is when you are trying to start an iPhone that has been discharged for a long time. If the battery runs low, you need to wait 15-60 minutes and only then press the Home or Power button.

Similar articles

The phone does not respond as before - we perform a hard reboot:

• press the power and “Home” buttons immediately (for 7th generation gadgets – “Power” and the volume button)
• wait 10-20 seconds until the Apple logo appears on the device display
• release the buttons - the operating system will start in approximately one minute

IPHONE 5 CHARGES BUT WILL NOT TURN ON (SOLVING THE PROBLEM)

Indicator shows charging but not charges Subscribe to the channel, like it :) Bought it.

How to turn on Iphone 5, 5s, 5c if it is charging but not turns on(one of the methods)

For anyone who would like to give back in kind, here is the link:

Similar articles

This method also helps with other problems. For example, when the program hangs or there is no response to the buttons.

When the Apple logo flashes and then disappears again, it is necessary to restore it. Most likely, the battery died due to a software failure. The error was caused by an unsuccessful iOS update or downloading and installing unlicensed software.

• launch iTunes on your computer and plug the USB cable into the connector
• turn off the phone using the combination Home buttons and Power (if you have an iPhone 7, use the volume button instead of Power)
• Press and hold the Home button and connect to your computer
• hold Home until the phone screen starts showing the iTunes logo and the plug icon
• The computer monitor should display the message “There is a problem with the iPhone; it needs to be updated or restored"
• confirm the restoration

Download and installation procedure latest version iOS will take about 30-40 minutes. There is another recovery method - DFU mode. Why doesn't my iPhone turn on, what should I do? Real instructions. It helps even if the iPhone doesn’t turn on and doesn’t respond to anything, try it. iPhone won't turn on while charging, what should I do? when the indicator shows charging but not. The iPhone is charging, but does not turn on - reasons for the lack of charge. We check chargers and learn how to restore batteries, and send iPhones for repairs. The method is specific because it destroys all data on the phone. If your iPhone won't turn on, what should you do? If it doesn't turn on, the iPhone won't turn on after. Stages:

• connect the charger (charge level must be greater than zero)
• After 5 minutes, disconnect the charger, connect the phone to the computer (desktop or tablet) and turn on iTunes
• immediately press Home and Power, hold them for exactly 10 seconds, then release the on and off button
• hold “Home” (15-30 seconds) until notified in iTunes (there should be nothing on the phone display when entering DFU mode)

Next, you should confirm the function and click on the “Restore” button. If you forget to overwrite data from your phone, you can cancel the recovery: disconnect the USB cable, hold down Home and Power for 10 seconds. Then the iPhone will reboot.

If everything is fine with the software, inspect the connector for dirt. Debris clogged in Lighting should be carefully removed using means at hand, for example, a toothpick.

When charging the battery from a computer, consider the functionality of the USB port. Maybe there is not enough current - try a regular Apple charger.

Pay attention to the charger itself. Even if the unique Apple cables are fragile - the braiding and cores are simply damaged - what can you expect from cheap Chinese products. The phone can stand for a long time and demonstrate charging, but it will still be zero if the charger is fake or broken. Use only unusual charging to avoid similar problems. iOS 10: how to install iOS 10 on iPhone Apple is working on the task with its unique operating system whose name is iOS. It is designed for Apple products. Both mobile phones and tablets work with it. But, just like any other computer software, iOS becomes outdated over time. As a result, she has to...

If the above actions were unsuccessful, most likely the battery was discharged due to natural wear and tear, industrial defects or damage. If your phone is dropped or flooded, don’t even look at the indicator: take the device for repair as quickly as possible or call a specialist home.

Separately, it is worth mentioning the case of changing the clocks on January 1, 1970. When someone jokes like this, the phone doesn’t turn on either - it constantly reboots, and doesn’t go beyond the logo. In such a situation, you should expect the battery to run down to 100% - only after complete discharge can you return to functionality. In order not to wait for a very long time, you need to contact a workshop or do it yourself: disassemble the phone, remove the battery, plug it in again and assemble the phone. Then the date is reset, and he again turns on. iPad or iPod touch does not turn on or does not respond, is not recognized in iTunes or displays. Independent action is possible if you have the skills and professional tools(suction cup, tweezers, spatula).

Where to go for iPhone repairs

When iPhone charges, but does not turn on, the best option - in terms of price, timing and quality - is to order a service on Yuda. One of the main advantages of the service is mandatory verification. All performers undergo a special check and confirm the accuracy of the data. Their profiles contain the following information.