Shtrikh-FR-K, modification "stump"
Introduction. There is such a wonderful KKM - Shtrikh-FR-K with an enormous service life. But the KKM has one serious drawback, it has non-standard dimensions, namely, a great length, for which it received the nickname "log" However, among the mechanics of the central heating center, another modification is widespread - "stump". Despite the seeming capital of the alteration, the "stump" is done quite simply and quickly, and after the revision, the scope of application expands significantly.
Task. Get a small-sized ASPD / NIM with a high level of reliability, low price and Shtrikh protocol.
Implementation.
Locksmith work.
The body is sawn in two stages, first the plastic, assembled into a single body together with the lids, then separately the iron. Moreover, the iron is cut in such a way that the plastic of the case is longer than the iron base. In this case, two threaded holes should remain on the iron base, they will come in handy later.
We cut off the iron so that there is a gap of 1, and at the same time there are holes with a thread 2.
In the above photo - a defective modification of the stump, in fact, gap 1 is only 3-4 mm.
The back wall is fastened with two screws.
We fasten the back wall with two bolts, since gluing requires more precise processing and adjustment. After we have screwed on the future back wall, draw a contour with a pencil and cut out the desired contour with a drimmel, it turns out poorly, but quickly.
Glue the remnants of the back top cover to the body.
We glue the remnants of the back top cover on superglue, or on dichloroethane - it also grasps plastic well, it's a matter of taste. In any case, there is enough surface for the glue hold.
Assembled version, ready for use.
To fasten the plastic case to the iron base, three factory mounting bolts are enough. We install the second set of rubber feet as close to the rear corners as possible, so it turns out more stable.
Electronics.
This revision point is optional, although the implementation of this point saved me from trips to the point several times. To do it or not is a personal matter for everyone. The essence of the revision is to block the head and paper sensor of the control printer. Now, even if a competent user decides to fill in the settings from another FM, which has a control printer turned on, this will not lead to a breakdown of the device.
Modified motherboard.
As you can see, all the revision is two wiring, that is, the process itself will not take much time.
- Thermal head opening sensor - pin 8 of the XS2 connector to ground
- Paper sensor - pin 6 of the XS2 connector to ground.
Modification of the XS2 connector for operation without a printer. Pins 6 and 8 are connected to ground.
The actual revision process is complete.
Conclusion. It should be noted against the backdrop of a decline in demand for PMM based on Shtrikh-FR-K, the "stump" modification is still popular, even despite the clumsy refinement. This is most likely due to the low price, Barcode exchange protocol and the incredible reliability of the Citizen printer.
A stub of ASPD A barcode can fit even in the smallest volume of the workplace.
"SHTRIKH-M-FR-K" is a new fiscal registrar from the leader of the cash register market with high-tech filling for a wide range of applications: for retail trade (from mini-shops "at home" to hypermarkets), catering establishments, gas stations, hotels, is there for all areas where reliable automation and high productivity are required.
Distinctive features.
High printing speed - up to 150 mm / sec;
- Automatic guillotine cutter;
- Fast loading of the receipt tape;
- Easy access to maintenance and replacement of EKLZ;
- Connection to PC via RS-232 or USB.
Great design.
The single-station fiscal recorder has been developed and designed by the team of the "SHTRIKH-M" company to the last detail: the device has an attractive and complete appearance, proposed by the specialists of the company's own design studio. The fiscal registrar with its clear straight lines of the body and smooth curves of the translucent lid will become the dominant feature of the cashier's workplace and will perfectly fit into both the classic interior and the hi-tech style store.
Reliability for years.
The printing mechanism of the fiscal registrar was developed by the company's designers, taking into account the vast experience of our specialists in this area. The design of the printing mechanism of the printer was built with a margin of safety, sufficient even for the most severe operating conditions in hypermarkets and supermarkets. The high-quality thermal head of the ROHM company (Japan) with a resource of 50 km provides excellent printing of receipts even at a speed of 150 mm / sec. The durable plastic of the case is resistant to mechanical stress, guarantees the durability of the device, and the design is simply pleasing to the eye. Automatic cutting unit (Taiwan) with a guillotine-type knife allows you to perform both full and partial cutting of a check. Moreover, even the ingress of foreign objects, for example, coins, into the cut-off unit will not lead to its breakdown: the electronics will automatically stop the knife.
Ribbon width and receipt format: freedom of choice.
The fiscal registrar "SHTRIH-M-FR-K" can print not only on a wide tape of 80 mm (there can be up to 57 characters in a line), forming representative and informative receipts, but also on the most common tape of 57 mm, thus allowing save on consumables. A wide selection of fonts (several sizes, italicizing or bold text), internal check format tables and printing of graphic logos make it possible to customize the appearance of checks at your discretion.
No downtime belt replacement.
In the fiscal registrar "SHTRIKH-M-FR-K" fast loading of the receipt tape is realized: you just need to insert a new one instead of the finished roll and close the lid - this is less than 5 seconds!
Easy to maintain.
Originally developed as a fiscal registrar, "SHTRIKH-M-FR-K" is easy to maintain, which can be seen in practice by employees of service organizations and service centers. To get to the fiscal memory or replace the EKLZ, you need to unscrew only 2 screws and remove the plastic case. The spare parts and accessories for the fiscal registrar, which is entirely a Russian development, are always available and affordable. Reliability, minimum time for disassembly and assembly and available spare parts are additional profit for service centers and savings for end customers!
Versatility.
Fiscal registrar "SHTRIKH-M-FR-K" is a multi-interface, that is, it can be connected to a PC both via RS-232 and USB. This allows freeing up scarce COM ports for other peripheral equipment.
One of the advantages of the device is several mounting options: it can be installed both horizontally and, to save space on the cash register, be fixed with fixing screws in a vertical position and at any angle of inclination.
For manual separation of a check, the fiscal recorder is equipped with a comb.
Compatibility.
In "SHTRIKH-M-FR-K", as in all fiscal registrars of the company "SHTRIKH-M", data exchange with a PC is implemented on the basis of a single protocol and driver.
KKM performs the following operations:
* Sale, return of sale, purchase, return of purchase;
* Cash sale;
* Sale on credit / for non-cash payment (up to three types of payment);
* Multiplying the price by the quantity of goods;
* Accrual of interest-free allowances and discounts;
* Accounting for monetary amounts;
* Calculation of subtotals;
* Calculation of the overall results;
* Calculation of the amount of change;
* Cancellation of the operation (partially and completely) in an open check;
* Calculation of the percentage mark-up and discounts for the entire check;
* Cancellation of a check;
* Cash payments from the cash desk, not related to the purchase;
* Entering amounts of money to the cashier;
* Allocation of taxes at established tax rates;
* Formation of non-fiscal reporting documents: daily reports without cancellation, reports by departments, reports on taxes;
* Taking readings of cash and operational registers with automatic printing;
* Cancellation of cash and operational registers (daily report with cancellation) with automatic printing;
* Repeat printing of the last fiscal document;
* Formation of short and complete fiscal reports;
* Formation of reports EKLZ;
* Printing of non-fiscal text information;
* Printing graphics (eg logos).
Contents of delivery.
KKM "SHTRIKH-M-FR-K" with installed EKLZ 1 pc.
Power supply unit with power cable 1 pc.
Interface cable for connecting cash register to PC 1 pc.
Receipt tape 1 roll
CD with software and documentation 1 pc.
Operating instructions 1 pc.
Tax inspector's instruction 1 pc.
Form 1 pc.
KKT passport 1 pc.
Passport of the version of the KKM model 1 pc.
Additional list for passport version 1 pc.
EKLZ passport 1 pc.
| Model | Fiscal registrar "Shtrih-M-FR-K " |
| Seal | |
| Printing method | Direct thermal |
| Printhead |
ROHM, Japan |
| Print speed |
150 mm per second |
| Number of characters per line | 48 characters (when printed in standard font) |
| Print area |
72mm or 576 dots |
| Cutter | There is |
| Cutter resource | 500,000 cycles |
| Fiscal memory | |
| Maximum number of shift totals | 2000 |
| Maximum number of re-registrations | 5 |
| Information storage period in fiscal memory |
At least 40 years old |
| Expendable materials | |
| Receipt tape type |
Check thermal tape (thermochemical) |
| Width, mm |
80 |
| Roll diameter, mm |
83 |
| Winding length, m |
80 |
| Bobbin bushing diameter, mm | 12 |
| Check tape thickness, microns |
60 to 120 |
| Physical parameters of the fiscal registrar | |
| Length, mm |
150 |
| Width, mm |
130 |
| Height, mm |
255 |
| Weight, kg |
1,6 |
| Colour | Combined, gray + black |
| Electrical parameters of the fiscal recorder | |
| Nutrition |
Through a power supply unit from an alternating current with a frequency of 50-60 Hz, a voltage of 100-240V |
| Power consumption |
No more than 48 W |
| Operating conditions | |
| Operating temperature range, |
+10 ° C to +40 ° C |
| Periphery | Computer, Cash Drawer |
| Interfaces |
1xDB25 (RS-232, PC), 1xRJ12 (cash drawer) |
| Software | Free drivers: Win9x / NT / Me / 2000; Test utilities; Programming examples; Detailed Documentation, Tax Inspector Program |
Prices: Without FN, with FN for 15 months, With FN for 36 months.
Belt width: 57 mm
Overview:
This model does not support the requirements of the FZ-54 law. To modernize the fiscal registrar, it is not necessary to replace it. Created for this retrofit kit FR Shtrikh-M.
Contents of delivery:
- Fiscal registrar Shtrikh-M FRK
- External power supply
- PS-232 or RS-USB cable
- 1 roll of receipt tape 80mm
- CD with drivers
- passport, operating instructions, tax inspector's instructions, version passport
The package includes driver barcode m frk (download) and instructions for connecting Shtrih m frk to 1s. (download). Also, the developer of the fiscal registrar distributes the cash program "Shtrikh-M: Cashier's Workplace" (download) free of charge. The commercial equipment of this company has proven itself well in the Russian market.
Appearance and convenience
Fiscal registrar Shtrikh M FR K is a cash register designed to be connected to a computer in on-line mode. Another product from the Shtrikh-M company, designed to replace the outdated, but still very popular fiscal registrar, Shtrikh FR-K. KKM Shtrikh M FR-K has a more compact body, an updated processor board and an improved algorithm of operation.
Shtrikh M PRK is perhaps the most popular fiscal registrar in Russia due to the company's long presence in our market and good technical support. Recently, it began to lose ground due to its high cost in front of new competitors.
Available in three colors: white, gray and black, but the top cover is always black.
Display
The display consists of 2 LEDs:
- red - signals an error
- green - signals that the fiscal recorder is included in the 220 volt network
Nearby there is a button to feed the receipt tape.
Connecting to devices
Has two ports for connecting external devices - one for a computer - LPT port, the other for connecting a cash drawer or a call to the kitchen. Unfortunately, there is no USB port, but the package may include a USB - LPT adapter. There have been cases when the fiscal registrar does not work well through the USB interface, therefore, whenever possible, the Shtrih-M PRK is connected via a COM port.
You can buy FR Shtrikh-M PRK, the price of which, although a little more expensive than analogues, but the difference pays off due to the reliability of the cash register, and you can order the connection of the fiscal registrar to 1C accounting (or another program) in our online store. Service engineers of our TEC will connect the cash register to a computer and train personnel on how to work with cash register machines. 1C and Shtrikh-M PRK work great together in one of the largest retail chains in Russia.
a printer
Over time, pieces of paper are hammered under the knife of the automatic receipt tape cutter.
Not a reliable cutter of the receipt tape, often jams. You have to scroll the knife roller manually, for this there is a technological hole under the top cover of the printer.
When a paper jam occurs, do not try to pull it out of the paper with foreign objects - you can easily damage the teeth of the metal paper cutter.
Types of basic cash register receipts and reports
Bar M FR K can print logos on cash register receipts.
| Cash register receipt | Morning X - report without cancellation | Evening Z report with cancellation. |
Nutrition
Impression
Cons of a fiscal registrar
- unreliable knife slicing cash register receipts
- weak technical characteristics
- lack of USB - port
Applications
- retail and wholesale
Fiscal registrar / printer settings before connecting to a computer
- download, unpack and install the driver for working with the fiscal registrar
- connect the power supply to the fiscal recorder
- connect the computer communication cable (COM or USB)
- turn on the power switch on the fiscal recorder
- run the "Driver Test" program
Start → All Programs → SHTRIH-M → Driver FR 4.10 → Driver Test FR 4.10
In the running driver, click the button: "property settings"
In the pop-up window, click the "Search for equipment" button
click "Start"
After the driver finds the equipment TWICE CLICK THE MOUSE on the found fiscal registrar Shtrikh-M-FR-K:
Click the "test connection" button, the name and serial number of your registrar will appear, then click the "OK" button.
Driver Installation
- IMPORTANT! When connecting the fiscal registrar to Windows 7, additional drivers are required (you can download them right here) -Drivers for Shtrih-FR-K.
- Please note that for the device to work correctly, you need to install them 2 times!
SHTRIKH M FR K connection to 1C v8.1 / 8.2
Typical configuration "Retail 1.0"
1) Install the SHTRIKH-M driver from the disk that comes with the FR.
2) It is necessary to rewrite from the folder ... Program Files SHTRIKH-M Driver FR 4.10 all files with the * .dll extension to the directory of the 1C platform (..Program Files1Сv81in)
3) Register the DrvFR.dll file in the system registry using the regsvr32 command "[path to the file] DrvFR.dll" (if, for some reason, registration did not occur automatically in the installation reason).
4) Connect the phased array to the PC.
5) Start 1C: Enterprise.
6) Open the menu "Service" -> "Shop equipment" -> "Assistant for connecting and setting up shop equipment".
7) In the form window, select "Fiscal registrars" press add.
8) In the form of the opened equipment directory, press add again, in a new window select the processing ShtrihMFiscalPrinters_v2.epf, model, write the name, then the button "write" and "ok" select this device.
9) Select the cashier, press the parameters. Select COM port, speed, press "ok".
10) The device is connected, you can get to work :)
Modernization of Shtrih cash registers to the "online" version is carried out using the upgrade kit, which includes:
- The modernization device (UM) is a special board that connects to the main board of the KKT and takes over the management of the cash register. A fiscal drive and one of the data transfer channels to the OFD (Ethernet, RNDIS, Wi-Fi) are connected to the UM. The UM is universal and is suitable for all KKT Shtrikh.
- Passport for the modernized cash register;
- Nameplate with the serial number and the name of the KKT;
- Cable for interfacing the UM with the main board of the KKT;
- Cables for connecting the UM to the Internet (Ethernet or USB).
- Computer (laptop);
- AVR programmer;
- Modernization kit for checkouts Shtrikh-M (photo above);
- Fiscal accumulator;
- COM cable for Shtrih-FR-K (with a COM-USB adapter cable);
- USB cable (for connecting the programmer to a computer);
- Screwdrivers (Phillips and flat);
- Drill with a drill for metal (d = 10 mm);
- Program Phased array driver test Hatch;
- Program Atmel Studio 7.0;
- Firmware file for the Shtrikh-FR-K motherboard;
Note 1... After modernization, KKT will receive the name Shtrih-FR-01F(instead of Shtrikh-FR-K) and a new serial number. Under this name and number, the CCP will be listed in the register of the tax service upon registration.
Note 2. Before starting the modernization, you need to make sure that the cash register is deregistered with the tax authorities. To deregister old CCPs from the tax office, it is necessary to print out fiscal reports for the period of operation of the CCP and submit them to the tax service together with the application for deregistration. After the modernization, it will no longer be possible to do this.
Note 3. Before starting the modernization, you need to make sure that the Shtrikh-FR-K fiscal registrar is serviceable and functioning normally. To do this, you need to connect it to the computer and through the program Phased array driver test Barcode to check its performance.
The procedure for upgrading the Shtrikh-FR-K:
1. Disconnect the power supply and all cables connected to the checkout. Remove the two top covers.
2. Pull out the receipt tape and disconnect the transaction log rewinder (the bin on which the paper is wound) from the second compartment. 
3. Unscrew the 4 screws that secure the plastic case of the cash register with the metal base. 
4. Lay the cash register on its side, use a flat screwdriver to bend the side latches of the case and detach the upper plastic case of the device.
5. Disconnect the EKLZ and remove the flexible drive from the second printing device. 
6. Use a Phillips screwdriver to unscrew the rewinder gear plate.
7. Remove the two screws securing the second printing device. It will no longer be needed for the checkout to work.
Note... Do not throw away the removed "signet". It will be needed for replacement, in case of breakage of the first "seal".
8. Unscrew the two screws on the bottom housing cover and detach the bottom cover. 
9. Disconnect all cables from the system board.
10. Unscrew the two screws securing the fiscal memory unit and detach it.
11. Set the system board aside. Take a drill and drill a hole in the metal base of the cash register, approximately in the place shown in the figure. This hole is required for the Ethernet cable.
Advice. It is better to first drill the hole with a small diameter drill, and then expand it with a 10 mm drill.
12. The walls of the hole can be sanded to smooth out burrs.
13. Make sure that the power switch on the KKT board is off. Connect the power supply to the board and insert the plug into the network. Connect the programmer to the KKT board, and connect the programmer to the computer using a USB cable.
Important! The connectors for connecting the programmer and the fiscal memory unit are the same. They can be easily confused. The connector for the programmer is located next to the COM port connector (shown in red in the figure).
After you have made sure that the programmer is connected to the correct connector, turn on the power on the board using the switch.
14. Run the program on the computer Atmel Studio 7.0... In the main menu of the program, select " Device Programming".
15. Specify the settings as shown in the photo, and then press the " Apply" (1), " Read"(2) and the second button" Read"(3). The program should read the signature of the device and show the output voltage. If this did not happen, check the connection of the programmer to the KKT motherboard. 
16. On the left in the menu, select " Memories". In the program window, select the location of the firmware file (1) and click the" Program" (2).
17. The process of flashing the system board will start. The green status bar at the bottom of the program will inform you about the progress of the operation.
18. In case of successful completion of the firmware, on the left, at the bottom of the program, messages will appear:
- Programming Flash ... OK
- Programming verifying ... OK
19. After flashing the microcontroller, you need to additionally flash the "fuses". To do this, on the left in the menu, select " Fuses".
Uncheck the box " M103C", mark the rest of the items as in the photo below. To start the firmware, click the" Program".
After the message " Verify registers ... OK"- turn off the board power using the switch and close the program.
20. Install the fiscal unit in the upgrade unit.
21. Fix the retrofit device to the site where the EKLZ was previously located. Insert the Ethernet cable into the drilled hole through the grommet. Connect the Ethernet cable and interface cable to the upgrade device.
Important! Make sure that the cables from the PA do not pass over the hole where the case fixing screw is screwed. Otherwise, some wire may be damaged.
22. Connect the other end of the interface cable from the PA to the connector on the system board (highlighted in red in the figure).
Note. The interface cable included with the upgrade kit may be short. In our case, we had to extend the cable.
23. Connect the remaining cables to the connectors on the system board.
24. Next, it is recommended to check the operation of the cash register. To do this, without assembling the body of the device, insert the paper into the printing device, connect the power supply to the device, and connect the device to the computer using a COM cable. After that, turn on the power on the fiscal recorder.
25. Run the program on the computer " Phased array driver test". At the bottom of the program window, click the" Setting properties".
26. In the window that appears, click the " Equipment search".
27. Press the " Begin". The registrar must determine the name" SHTRIKH-FR-01F". Click on the line with the name twice with the left mouse button.
28. When you click on the " Connection check"you can see that the recorder has no serial number. Press the" OK".
29. To enter the serial number, select " Service". Enter the serial number (located in the passport of the KKT or on the nameplate) and press the button" Write down".
30. For the stable operation of the cash register, it is recommended to update the firmware of the upgrade device, since at the time of the upgrade it could already be outdated. To check the version of the UM software, select the item on the left " State"and press the button" Long query ".
31.
Turn off the recorder and remove the paper. Assemble the case and tighten all the screws that secure it. Fiscal registrar under a new name " Shtrih-FR-01F"ready to go online."
RS: Do not forget to stick a new nameplate with the KKT serial number.
